Serviceability behavior of High Strength Concrete I-beams reinforced with Carbon Fiber Reinforced Polymer bars

محتوى المقالة الرئيسي

AbdulMuttalib I. Said
Oday Mohammed Abbas

الملخص

Fiber Reinforced Polymer (FRP) bars are anisotropic in nature and have high tensile strength in the fiber direction. The use of High-Strength Concrete (HSC) allows for better use of the high-strength properties of FRP bars. The mechanical properties of FRP bars can yield to large crack widths and deflections. As a result, the design of concrete elements reinforced with FRP materials is often governed by the Serviceability Limit States (SLS). This study investigates the short-term serviceability behavior of FRP RC I-beams. Eight RC I-beams reinforced with carbon-FRP (CFRP) and four steel RC I-beams, for comparison purposes, were tested under two-point loading.
Deformations on the concrete and crack widths and spacing are measured and analyzed. A discussion on the main aspects of the SLS of FRP RC is introduced. The service load that fulfills the serviceability requirements, at a cross-section level, ranges between 0.27 and 0.38 times the ultimate load for sections dimensioned to fail in concrete crushing. The determinant criterion is the deflection limitation

تفاصيل المقالة

كيفية الاقتباس
"Serviceability behavior of High Strength Concrete I-beams reinforced with Carbon Fiber Reinforced Polymer bars" (2013) مجلة الهندسة, 19(11), ص 1515–1530. doi:10.31026/j.eng.2013.11.10.
القسم
Articles

كيفية الاقتباس

"Serviceability behavior of High Strength Concrete I-beams reinforced with Carbon Fiber Reinforced Polymer bars" (2013) مجلة الهندسة, 19(11), ص 1515–1530. doi:10.31026/j.eng.2013.11.10.

تواريخ المنشور

المراجع

ACI 234R-96 (2000), “Guide for the Use of Silica Fume in Concrete”, American Concrete Institute.

ACI Committee 318. (1995). "ACI 318-95. Building code requirements for structural concrete (ACI 318-95) and commentary (ACI 318R-95)." American Concrete Institute.

ACI Committee 440. (2006). "ACI 440.1R-06. Guide for the design and construction of concrete reinforced with FRP bars." American

Concrete Institute.

Beeby, A. W. (2004). "The influence of the parameter φ/ρeff on crack widths." Structural Concrete, 5(2), 71-83.

CAN/CSA. (2002). "CAN/CSA-S806. Design and construction of building components with fibre-reinforced polymers." Canadian Standards

Association, Ontario, Canada, 177pp.

CEN. (2004). "Eurocode 2: Design of concrete structures - Part 1.1: General rules and rules for buildings (EN 1992-1-1:2004)." Comité

Europeen De Normalisation, Brussels.

fib. (2007). "FRP reinforcement in RC structures." Féderation International Du Béton, Fib Task Group 9.3, Fib Bulletin 40, Lausanne,

witzerland, September 2007, 147pp.

ISIS Canada. (2001). "Reinforcing concrete structures with fibre reinforced polymers –Design manual No. 3." ISIS Canada Corporation.

University of Manitoba, Manitoba, Canada, 158pp.

Nanni, A. (2003). "North American design guidelines for concrete reinforcement and strengthening using FRP: Principles, applications and unresolved issues." Construction and Building Materials, 17(6-7), 439-446.

Raffaello, Fico (2008),” Limit States Design of Concrete Structures Reinforced with FRP Bars”, Ph.D. thesis, University of Naples Federico II.

Silica Fume Association, 2005, “Silica Fume User’s Manual,” Publication No. FHWA-IF-05-016, Federal Highway Administration, Washington, DC

المؤلفات المشابهة

يمكنك أيضاً إبدأ بحثاً متقدماً عن المشابهات لهذا المؤلَّف.