NUMERICAL STUDY OF INCOMPRESSIBLE FLOW AND HEAT TRANSFER IN NON-CIRCULAR DUCTS WITH CUSP CORNERS
Main Article Content
Abstract
A numerical finite-volume calculation method was used for application to fully-developed flow and heat transfer in straight ducts with 2-Cusp, 3-Cusp and 4-Cusp cross-sectional area. The method was formulated with reference to a non-orthogonal curvilinear coordinate system which was fitted exactly into duct shape. In turbulent flow, the Reynolds stresses were calculated by using the coupled algebraic stress model of Launder and Ying (1973) with a (k ) transport model. This turbulent stress model enabled secondary flows to be included in the non-circular duct calculations. In heat transfer solution, three thermal boundary conditions were investigated. Predictions were compared with available numerical and experimental data. The turbulent flow predictions of secondary and axial velocity, wall shear stress and Nusselt number were in reasonable agreement with experiment for the fully-developed flow cases. It is concluded that, although the maximum secondary flow was found to be (1.5%-2.5%) of the mean axial flow, the absence of this flows have significant influence on the flow and heat transfer parameters. Moreover, these flows will increase when the corners of a duct become more acute. Heat transfer results showed that the peripheral temperature variation around the duct has a significant effect on
the heat transfer results, and confirmed the inadequacy of the hydraulic radius concept in the cases of the very non-circular ducts when comparison is made with Blasius correlation.
Article Details
How to Cite
Publication Dates
References
Gunn, D.J. and Darling, M.D. (1963), Fluid Flow and Energy Losses in Non-circular Conduits, Trans. Inst. Chem. Engrs., Vol. 41, pp. 163.
Hassan, A.K.A. (1984), Forced Convection in Isosceles Right Angle Triangular and 4-Cusp Ducts, Ph. D. Thesis, University of Liverpool, U.K.
Hinze, J.O. (1975), Turbulence, McGraw-Hill, New York.
Jones, W.P. and Launder, B.E. (1972), The Prediction of Laminarization with a Two-equation Model of Turbulence, Int. J. Heat Mass Transfers, Vol. 15, pp. 301.
Karki, K. and Patankar, S. (1989), Pressure Based Calculation Procedure for Viscous Flows at All Speeds in Arbitrary Configurations, AIAA Journal, Vol.27, pp. 1167-1174.
Kays, W.M. and Crawford, M.E. (1993), Convective Heat and Mass Transfer, 3rd edition, cGrawHill, New York.
Launder, B.E. and Spalding, D.B. (1974), The Numerical Computational of Turbulent Flow, Computer Methods in Applied Mechanics and Engineering, Vol.3, pp. 269-289.
Launder, B.E. and Ying, W.M. (1973), Prediction of Flow and Heat Transfer in Ducts of SquareSection, Proc. I. Mech. E., Vol. 187, pp. 455.
Patankar, S.V. (1980), Numerical Heat Transfer and Fluid Flow, Hemisphere, McGraw-Hill, New York.
Patankar, S.V. and Spalding, D.B. (1972), A Calculation Procedure for Heat Mass and Momentum Transfer in 3D Parabolic Flows, Int. J. Heat Transfer, Vol.15, pp. 1785.
Rapely, C. W. (1980), Fluid and Heat Flow in Tubes of Arbitrary Cross-Section, Ph.D. Thesis, University of London, U.K.
Rhie, C. M. (1985), A Three-Dimensional Passage Flow Analysis Method Aimed at Centrifugal Impellers, Computers and Fluids, Vol. 13, No. 4, pp. 443-460
Rijab, M.S., Hassan, A.K.A. and Muhsen, S.A. (1991), Turbulent Fluid Flow in Three-Cusp Duct,
Rokni, M. and Gatski, T.B. (1999), Predicting Turbulent Convective Heat Transfer in ThreeDimensional Duct Flows, NASA/TM-1999-209843.
Shah, R.K. and London, A.L. (1978), Laminar Flow Forced Convection in Ducts, Advances in Heat Transfer, Academic Press, New York.
Versteeg, H.K. and Malalasekera, W. (1995), An Introduction to Computational Fluid Dynamics, the Finite Volume Method, Longman Scientific and Technical.