AN EXPERIMENTAL STUDY OF BURR FORMATION IN DRILLING AND SLOT-END MILLING OPERATIONS
محتوى المقالة الرئيسي
الملخص
This paper presents the results of an experimental study on the influence of the main cutting parameters on burr formation and its types in drilling and slot-end milling operations to machine low carbon and stain -less steels using HSS cutting tools and cutting fluid. Particular attention was focused on the relation between the burr type and size and cutting parameters. Therefore, a wide range of cutting speeds, feed rates, and dept of cuts were investigated to explore the optimum cutting conditions. Burr heights were measured and anal- lyzed at different machining conditions to determine the effect of the cutting speed, feed rate, and depth of cut on burr formation. The data obtained for low carbon steel were compared with those for stainless steel. Different diameters of HSS twist drills were used to observe their effects on drilling burr formation. The quantitative measurements of burrs height yield much useful information because relatively uniform small and large burrs were formed under these conditions
تفاصيل المقالة
كيفية الاقتباس
تواريخ المنشور
المراجع
Kim, J. and Dornfeld, D. A., “ Development of an Analytical Model for Drilling Burr Formation in Ductile Materials”, Transactions of the ASME, vol.124, 2002, pp.192-198.
Kim, J., Min, S., and Dornfeld, D. A. ,“ Optimization and Control of Drilling Burr Formation of AISI 304L and AISI 4118 Based on Drilling Burr Control Chats”, Int. J. of Machine Tools & Manufacture, 41, 2001, pp 923-936.
Dechow. H., “Influence of Tool Geometry on Hole Quality When Drilling Ti-6Al-4V”, LMA Report, 1998.
Ko., S. –L and Chang, J. E., “ Development of Drill Geometry for Burr Minimization in
Drilling “, 2nd. Asia Pacific Fourm on Precision Surface Finishing and Deburring Technology,
22-24,2002, pp135-150.
Min, S., Dornfeld, D. A., and Nakao, Y., “ Influence of Exit Surface Angle on drilling Burr
Formation”, J. of Manufacturing Science and Engineering, vol. 125, Nov. 2003, pp. 634-644.
Kim, J., “ Preliminary Experimental of Drilling Burr Formation in Titanium Alloys ”, LMA Report, 1998.
Olevra, O. and Barrow, G., “ An experimental Study of Burr Formation in Square Shoulder Face Milling ” , Int. J. of Machine Tools & Manufacture, vol. 36, No.9 , 1996, pp. 1005-1020.
Chu, C. H., “ Exit Burr Minimization by Selecting Tool Feed Direction ” ,LMA Report, 1998.
Choi, I. H. and Kim, J. D., “ Electrochemical Deburring System Using Electroplated CBN Wheels ”, Int. J. of Machine Tools & Manufacture”, vol. 38, No. 1-2, 1998, pp. 29-40.
Gillespie, L. K., “ Burr produced by end-milling”, Bendix Report BDX-613-1503, 1976.
Donaldson, G., Lecain, G. H., and Gpoold, V.C., “Tool Design”, TATA McGraw-Hill Publishing Co., 3rd edition, 2000.
Lee, K. and Dornfeld, D. A., " Micro-burr formation and minimization through process
Control ", Precision Engineering 29 (2005) pp.246-252.
Degarmo, E. P., "Materials And Processes In Manufacturing", Macmillan Publishing Co., 1988.
Kalpakjia, S.,"Manufacturing Processes For Engineering Materials", Addison Wesly, 2000.
Kim, J., " Optimization and control of drilling burr formation in metals ", Ph.D. Dissertation,
Department of Mechanical Engineering, University of California at Berkeley, 2000.
Furness, R., High Speed Video of Drilling Burr Formation., AMTD, Ford Motor Company,
1998.
Guo, Y. B., and Dornfeld, D. A.,“ Finite element modeling of burr formation process in drilling 304 stainless steel”, J. of Manufacturing Science and Engineering, vol.122, Issue 4, pp. 612-619, Nov.2000.
Lee,K. and Dornfeld, D. A., " A study of surface roughness in the micro-end-milling process",
Laboratory for Manufacturing Automation, paper Kiha-03,2004.
Wright P. K., Dornfeld D. A., Wang, F. C., and Chu C. H., " Decision making in a multi-constraint agent-based process planning", Trans. of NAMRI, vXXVII , 2000.
Landers, R. G., Ulsoy, A. G. and Furness, R. J., " Process monitoring and control of machining operations ", Mechanical Systems Design Handbook, O: D. I. Nwokah and Hurmuzlu (eds.), CRC Press, Chapter 6, pp. 85-119, 2002.
Avila, M. C. and Dornfeld, D. A.," On the face milling burr formation mechanisms and minimization strategies at high tool engagement ", Laboratory for Manufacturing Automation, paper Miguel (-2-03), 2004.
Hashimura, M. and Dornfeld, D. A., “ Proposal of burr classification method based on the formation mechanisms in face milling”, J. Japan Society of Precision Engineering, Vol. 65, 6, pp. 872-87,1999.